[libcamera-devel] [PATCH] pipeline: raspberrypi: Set sensor default orientation before configure()
Laurent Pinchart
laurent.pinchart at ideasonboard.com
Mon Aug 10 07:38:11 CEST 2020
Hi Naush,
On Fri, Aug 07, 2020 at 01:12:01PM +0100, Naushir Patuck wrote:
> Hi all,
>
> Just a gentle ping for the below change to be submitted when you can.
I know I have a fairly large backlog of RPi libcamera patches to review,
I apologize about that, even more so as I will have very little time
this week. I'll do my best and try to address as much of the backlog as
possible on Thursday.
> On Tue, 21 Jul 2020 at 10:23, Naushir Patuck <naush at raspberrypi.com> wrote:
> >
> > The default sensor orientation must be set early on in match() to ensure
> > generateConfiguration() and configure() return out the correct Bayer
> > ordering to the application. This is particularly important for RAW
> > capture streams.
> >
> > Signed-off-by: Naushir Patuck <naush at raspberrypi.com>
> > ---
> > src/libcamera/pipeline/raspberrypi/raspberrypi.cpp | 14 +++++++-------
> > 1 file changed, 7 insertions(+), 7 deletions(-)
> >
> > diff --git a/src/libcamera/pipeline/raspberrypi/raspberrypi.cpp b/src/libcamera/pipeline/raspberrypi/raspberrypi.cpp
> > index bf1c7714..e9084afd 100644
> > --- a/src/libcamera/pipeline/raspberrypi/raspberrypi.cpp
> > +++ b/src/libcamera/pipeline/raspberrypi/raspberrypi.cpp
> > @@ -962,6 +962,13 @@ bool PipelineHandlerRPi::match(DeviceEnumerator *enumerator)
> > /* Initialize the camera properties. */
> > data->properties_ = data->sensor_->properties();
> >
> > + /* Configure the H/V flip controls based on the sensor rotation. */
> > + ControlList ctrls(data->unicam_[Unicam::Image].dev()->controls());
> > + int32_t rotation = data->properties_.get(properties::Rotation);
> > + ctrls.set(V4L2_CID_HFLIP, static_cast<int32_t>(!!rotation));
> > + ctrls.set(V4L2_CID_VFLIP, static_cast<int32_t>(!!rotation));
> > + data->unicam_[Unicam::Image].dev()->setControls(&ctrls);
> > +
> > /*
> > * List the available output streams.
> > * Currently cannot do Unicam streams!
> > @@ -1165,13 +1172,6 @@ int RPiCameraData::configureIPA()
> > { V4L2_CID_EXPOSURE, result.data[1] } });
> > sensorMetadata_ = result.data[2];
> > }
> > -
> > - /* Configure the H/V flip controls based on the sensor rotation. */
> > - ControlList ctrls(unicam_[Unicam::Image].dev()->controls());
> > - int32_t rotation = sensor_->properties().get(properties::Rotation);
> > - ctrls.set(V4L2_CID_HFLIP, static_cast<int32_t>(!!rotation));
> > - ctrls.set(V4L2_CID_VFLIP, static_cast<int32_t>(!!rotation));
> > - unicam_[Unicam::Image].dev()->setControls(&ctrls);
> > }
> >
> > if (result.operation & RPI_IPA_CONFIG_SENSOR) {
--
Regards,
Laurent Pinchart
More information about the libcamera-devel
mailing list